Discontinuous measurement
Discontinuous measurement records whether a behavior happened during, or at the end of, set intervals instead of capturing every instance. The three methods you need are partial interval recording, whole interval recording and momentary time sampling, and each one produces an estimate that leans in a predictable direction.
What does task A.2 ask a technician to do?
Task A.2 asks you to implement discontinuous measurement procedures as the plan describes. In practice you split an observation into equal intervals, watch for the target behavior, and score each interval by the rule for the chosen method. You then report the percentage of intervals scored. You do not pick the method; your supervisor does.
These methods exist because counting every response is often impossible while you are also teaching. A behavior that happens dozens of times a minute, such as hand flapping, or one with no clear start and end, such as humming that fades in and out, is hard to count accurately. Sampling it in intervals gives a workable picture with far less effort.
The price of that convenience is accuracy. Because you are scoring intervals rather than responses, the result is a percentage of intervals, not a count, and it can sit above or below the true amount of behavior.
How do the three interval methods differ?
Partial interval scores an interval if the behavior occurs at any point in it. Whole interval scores an interval only if the behavior lasts the entire interval. Momentary time sampling scores an interval only if the behavior is happening at the exact moment the interval ends. The scoring rule is the whole difference, and it drives the bias.
| Method | Score the interval when | Tends to | Often used for |
|---|---|---|---|
| Partial interval | The behavior occurs at any time in the interval | Overestimate | Behavior the plan aims to reduce |
| Whole interval | The behavior continues for the full interval | Underestimate | Behavior the plan aims to increase, such as on-task work |
| Momentary time sampling | The behavior is occurring at the instant the interval ends | Over- or underestimate; misses brief behavior | Ongoing behavior, or watching several learners |
Scoring each method, step by step
One habit matters more than the rest: never count instances inside an interval. If a learner spits three times in one 10-second partial interval, that interval gets one mark, not three.
- Read the operational definition and confirm the interval length on the data sheet, for example 10 seconds or 2 minutes.
- Set a vibrating timer or audio cue so you are not watching a clock instead of the learner.
- Partial interval: mark the interval as soon as you see one instance, then stop scoring that interval and wait for the next one.
- Whole interval: mark the interval only if the behavior ran unbroken from the first second to the last.
- Momentary time sampling: look up when the cue sounds and mark only what you see at that instant.
- At the end, divide scored intervals by total intervals and multiply by 100.
What do these methods look like in real sessions?
In a clinic, partial interval might track vocal stereotypy in 10-second blocks during table work. At school, whole interval might track whether a student stays engaged with a worksheet for each full 30 seconds. In a group home or day program, momentary time sampling lets one technician check several people every few minutes without constant watching.
Worked scenario: using 1-minute momentary time sampling, a technician sees a learner rock for 50 seconds of a minute, but the learner is still at the moment the cue sounds. That interval is scored as not occurring. The method is working as designed; it simply missed the behavior, which is exactly its weakness.
Second scenario: with whole interval recording, a child plays independently for 14 of 15 seconds and glances at the adult for one second. The interval is not scored, so the data understate how much independent play happened.
Which mistakes cost points on discontinuous measurement questions?
The usual errors are counting several instances in one interval, mixing up which method overestimates, scoring momentary time sampling from what happened earlier in the interval, and reporting a count instead of a percentage of intervals. Questions also test whether you would quietly switch methods. You would not; you would raise the concern with your supervisor.
- Partial interval overestimates; whole interval underestimates. Learn that pairing cold.
- Momentary time sampling looks only at the instant the interval ends.
- Results are a percentage of intervals, never a rate or a count.
- Interval methods are not continuous measurement, however short the intervals.
Who chooses the method, the RBT or the BCBA?
The supervising BCBA or BCaBA chooses the measurement system, the interval length and the operational definition, because those decisions shape every later treatment decision. The RBT collects the data exactly as written, keeps the timing accurate, and reports problems, such as a behavior too brief for the method to catch or intervals too short to score reliably.
Practice questions
A technician divides a work period into 15-second intervals. She marks an interval only if Ethan stays on task for the entire interval. Which method is she using?
A technician uses whole interval recording for Darius's independent play. He often plays for most of an interval but stops briefly near the end. How are these data most likely to compare with his actual play time?
Using momentary time sampling, a technician checks Owen 20 times during a session. He is rocking at 5 of the checks. What percentage of intervals should be recorded?
Using 10-second partial interval recording, a technician sees Lila spit three separate times within the same interval. How should that interval be scored?
Using 1-minute momentary time sampling, a technician sees Bella flapping her hands for nearly the whole minute, but she stops one second before the timer signals. How should that interval be recorded?
Questions people ask
Is a shorter interval more accurate?
Generally yes, because shorter intervals miss less, but they are harder to score. Your supervisor balances accuracy against what you can manage during teaching.
Can I use momentary time sampling for a brief behavior like a single hit?
It would miss most instances. That mismatch is something to flag to your supervisor rather than fix on your own.
Why would a plan accept a biased method?
Because the bias is known and consistent. If a reduction target is overestimated every session, a real drop still shows clearly on the graph.
How ready are you?
Ten questions, about 3 minutes, no account. Get your readiness score and your weakest domains.
Check my readiness