Momentary time sampling vs partial interval
Momentary time sampling scores an interval only if the behavior is happening at the exact moment the interval ends, while partial interval recording scores it if the behavior happens at any point during the interval. Partial interval tends to overestimate; momentary time sampling can over- or underestimate.
What is the difference between momentary time sampling and partial interval?
Both divide an observation into equal intervals and report the percentage scored. In partial interval, you watch the whole interval and mark it if the behavior occurs even once. In momentary time sampling, you only look at the end of the interval and mark it if the behavior is happening at that instant. What happens earlier in the interval does not count.
Because momentary time sampling needs only a glance at set moments, it frees the technician to teach between checks. It works best for behaviors that last a while, such as being out of seat or engaged with toys.
Partial interval needs constant watching but catches brief behaviors that momentary time sampling would usually miss.
Momentary time sampling and partial interval side by side
| Momentary time sampling | Partial interval | |
|---|---|---|
| Scored when | Behavior occurs at the moment the interval ends | Behavior occurs at any time in the interval |
| Observer attention | Only at the end of each interval | Throughout every interval |
| Typical bias | Can over- or underestimate | Overestimates |
| Best for | Ongoing, longer-lasting behaviors | Brief or high-rate behaviors |
| Usual target direction | Either | Often behaviors to decrease |
| Example | In seat when the 1-minute timer beeps | Any hand flap during a 10-second interval |
How do you tell momentary time sampling and partial interval apart on the exam?
Find the scoring rule for one interval. If the behavior only has to happen at the end of the interval, it is momentary time sampling. If any occurrence at any time earns the mark, it is partial interval. If the behavior has to last the whole interval, it is whole interval recording. Words like instant, moment or when the timer beeps signal momentary time sampling.
- Only the final moment counts: momentary time sampling.
- Any time in the interval counts: partial interval.
- The entire interval is required: whole interval.
Worked scenarios
Scenario 1. A session has ten 30-second intervals. The learner taps his pencil early in intervals 2, 5 and 8, but never at the end. Partial interval gives 30 percent; momentary time sampling gives 0 percent.
Scenario 2. Every 2 minutes, a technician looks up and records whether the learner is engaged with materials. Answer: momentary time sampling.
Scenario 3. A technician marks each 10-second interval in which a learner vocalizes at all. Answer: partial interval.
Scenario 4. A learner is out of seat for most of a session, sitting briefly just as two timers beep. Answer: momentary time sampling would underestimate the out-of-seat behavior here.
What are the common traps with momentary time sampling vs partial interval?
The most common trap is scoring momentary time sampling based on what happened during the interval rather than at its end. Another is assuming momentary time sampling always underestimates, like whole interval does. It can err in either direction. A third is reporting a percentage of intervals as a count of how many times the behavior happened.
- Scoring a momentary interval because the behavior happened earlier.
- Assigning momentary time sampling a fixed bias.
- Using momentary time sampling for very brief behaviors.
When would you see each in a session?
Momentary time sampling is common in classrooms and group settings, where you check engagement or on-task behavior while also teaching. Partial interval is common for behaviors targeted for reduction, like vocal stereotypy or hand mouthing, where any occurrence matters. The supervisor chooses the method and interval length; you score each interval by its rule.
A vibrating timer or app keeps intervals accurate. Glancing at a wall clock often drifts and makes the data less reliable.
Practice questions
Using 1-minute momentary time sampling, a technician sees Bella flapping her hands for nearly the whole minute, but she stops one second before the timer signals. How should that interval be recorded?
Using 10-second partial interval recording, a technician sees Lila spit three separate times within the same interval. How should that interval be scored?
A supervisor explains that partial interval recording is often chosen for behaviors the team wants to reduce. What is the main reason?
Using momentary time sampling, a technician checks Owen 20 times during a session. He is rocking at 5 of the checks. What percentage of intervals should be recorded?
Questions people ask
Why would a team choose momentary time sampling?
It lets a technician collect data at set moments while still teaching, and it suits behaviors that last for a while.
Does partial interval tell you how many times a behavior happened?
No. It reports the percentage of intervals with at least one occurrence, not the number of occurrences.
How ready are you?
Ten questions, about 3 minutes, no account. Get your readiness score and your weakest domains.
Check my readiness