Duration vs latency

Duration measures how long a behavior lasts from its start to its end, while latency measures how long it takes a behavior to start after an instruction or cue. Both are timed, but duration is about the behavior itself and latency is about the wait before it.

What is the difference between duration and latency?

Duration starts the timer when the behavior begins and stops it when the behavior ends, answering how long. Latency starts the timer when the cue is given and stops it when the behavior begins, answering how quickly. A long tantrum is a duration problem. A learner who waits a minute before following an instruction is a latency problem.

Both measures need a clear operational definition of when the behavior starts. Duration also needs a clear definition of when it ends, such as five seconds of quiet after crying.

Duration can be reported per episode, as an average, or as total time across a session. Latency is usually reported per instruction or as an average.

Duration and latency side by side

DurationLatency
Timer startsWhen the behavior beginsWhen the cue or instruction is given
Timer stopsWhen the behavior endsWhen the behavior begins
Question it answersHow long did it last?How long before it started?
ExampleCrying lasted 4 minutesTook 25 seconds to start cleaning after the instruction
Goal often isShorter problem behavior or longer engagementFaster response to instructions
Measurement familyContinuousContinuous

How do you tell duration and latency apart on the exam?

Find where the timer starts. If it starts with the behavior, it is duration. If it starts with an instruction, cue or signal, it is latency. Then check where it stops. Duration stops when the behavior ends; latency stops when the behavior begins. If the timer runs from the end of one response to the start of the next, it is interresponse time.

  • Behavior start to behavior end: duration.
  • Cue to behavior start: latency.
  • End of one response to start of the next: interresponse time.

Worked scenarios

Scenario 1. A supervisor wants to know how long a learner stays engaged with a puzzle. Answer: duration.

Scenario 2. After hearing "line up," a learner takes 40 seconds to stand. The team wants that time to shrink. Answer: latency.

Scenario 3. A technician times each tantrum from first scream until the learner has been calm for 10 seconds. Answer: duration.

Scenario 4. A learner is asked to put on shoes, and the technician times from the request until the first shoe is picked up. Answer: latency.

What are the common traps with duration and latency?

The biggest trap is starting the timer in the wrong place. If a question says the timer begins at the instruction, the answer is latency even if the behavior then lasts a long time. Another trap is confusing latency with interresponse time. Latency is measured from a cue; interresponse time is measured from the previous response.

  • Timing from the cue but calling it duration.
  • Including the behavior itself in a latency measure.
  • Not defining when a behavior ends.

When would you see each in a session?

Duration appears for tantrums, crying, time on task, time in seat and independent play. Latency appears for compliance targets, such as responding to instructions or transitions, and for skills where speed matters. The supervisor writes which measure to take and the start and stop rules. Follow those rules exactly, since a moved start point changes the data.

A stopwatch or data app with a lap function makes both measures easier. Record each time right away rather than estimating at the end of the session.

Practice questions

Question 1 · Data collection and graphing

The plan says to record latency to compliance with "Clean up the blocks." The technician starts her timer when Ava begins picking up blocks and stops it when the last block is in the bin. What did she actually record?

Question 2 · Data collection and graphing

For which of these behaviors would duration recording give the most useful information?

Question 3 · Data collection and graphing

A supervisor wants to know how long a learner's tantrums last from start to finish. Which measure should the technician collect?

Question 4 · Data collection and graphing

A technician says, "Mateo, put on your shoes," starts a stopwatch, and stops it the moment Mateo reaches for his shoes. What is she measuring?

Questions people ask

Can one behavior be measured with both duration and latency?

Yes. A team might track how long a learner takes to start a task and also how long they stay on it.

Is latency a continuous measure?

Yes. Latency is measured for each instance, so it belongs to continuous measurement.

How ready are you?

Ten questions, about 3 minutes, no account. Get your readiness score and your weakest domains.

Check my readiness