Latency vs interresponse time
Latency is the time from a cue or instruction to the start of a response, while interresponse time (IRT) is the time from the end of one response to the start of the next response. Both measure a gap before a behavior; they differ in what starts the clock.
What is the difference between latency and interresponse time?
Latency begins with something outside the behavior, such as an instruction, a question or a bell, and ends when the learner starts responding. Interresponse time begins when one instance of the behavior ends and stops when the next instance starts. Latency shows how quickly a learner responds to a cue; IRT shows how closely responses follow each other.
IRT is useful when the pace of a behavior matters. A learner who eats too quickly may need longer gaps between bites. A learner who reads slowly may need shorter gaps between words.
Latency is tied to instructions, so it is often used to track compliance and attending.
Latency and interresponse time side by side
| Latency | Interresponse time | |
|---|---|---|
| Clock starts | When the cue is given | When the previous response ends |
| Clock stops | When the response starts | When the next response starts |
| Question it answers | How quickly after the cue? | How much time between responses? |
| Needs a cue | Yes | No |
| Example | 8 seconds from "sit down" to sitting | 20 seconds between one bite and the next |
| Common target | Faster responding to instructions | Slower or faster pacing of a repeated behavior |
How do you tell latency and interresponse time apart on the exam?
Ask what starts the clock. If it is an instruction, prompt, signal or question, the measure is latency. If it is the end of a previous instance of the same behavior, the measure is interresponse time. If there is no cue mentioned and the scenario talks about gaps between repeated behaviors, interresponse time is almost always the answer.
- Clock starts with a cue: latency.
- Clock starts when the last response ends: IRT.
- Clock starts when the behavior begins: duration.
Worked scenarios
Scenario 1. A supervisor wants a learner to slow down while eating. The technician times from swallowing one bite to lifting the fork for the next. Answer: interresponse time.
Scenario 2. The teacher says "take out your book," and the technician times until the learner reaches for it. Answer: latency.
Scenario 3. A learner bites his nails in episodes. The team measures the time between the end of one episode and the start of the next. Answer: interresponse time.
Scenario 4. After a peer says "hi," a learner takes 12 seconds to reply. Answer: latency, because the peer's greeting is the cue.
What are the common traps with latency and interresponse time?
Both measure a pause before a behavior, so it is easy to mix them up. The trap is skipping the question of what started the timer. Another trap is measuring IRT from the start of one response instead of its end. A third is thinking a longer IRT is always good; whether you want longer or shorter gaps depends on the goal.
- Treating any pause as latency.
- Starting the IRT clock at the start of the previous response.
- Assuming the goal direction instead of reading the plan.
When would you see each in a session?
Latency is common in programs for following instructions, transitioning and responding to name. IRT is less common but appears for pacing targets, such as eating speed or the rate of a repetitive behavior. Your supervisor defines the start and stop points. Record each interval as it happens, since both measures depend on precise timing.
If the definition of when a response ends is unclear, ask before you start. IRT data are only as good as that definition.
Practice questions
A technician times the seconds between Kira finishing one worksheet item and starting the next. A coworker says this is latency. Why is the coworker incorrect?
A technician says, "Mateo, put on your shoes," starts a stopwatch, and stops it the moment Mateo reaches for his shoes. What is she measuring?
Priya, 16, eats very quickly at lunch. Her supervisor asks the technician to record how many seconds pass between the end of one bite and the start of the next. Which measure is this?
Questions people ask
Is IRT related to rate?
Yes. Shorter IRTs generally mean a higher rate, because responses are happening closer together.
Are latency and IRT both continuous measures?
Yes. Both are timed for each instance across the observation, so both are continuous.
How ready are you?
Ten questions, about 3 minutes, no account. Get your readiness score and your weakest domains.
Check my readiness